СвязьПроект
http://old.xdsl.ru/svpro/

GS1002 КОНФИГ ЗАГНУЛСЯ
http://old.xdsl.ru/svpro/viewtopic.php?f=4&t=3425
Страница 1 из 1

Автор:  qbq [ 15 июн 2013, 10:30 ]
Заголовок сообщения:  GS1002 КОНФИГ ЗАГНУЛСЯ

не один ip не отвечает в консоль приглашение не дает

конфигурационный файл не верный
консольный кабель паял как на циске
ctrl c x жал

в бут меню не пускает
что делать помогите!!!!!!!!

System Bootstrap, Version 1.2 Decompressing the image: ################################################################################ ################################################################################ ########################[OK] œ AddPac GS1002 Series (GS1002_G2) 32BIT RISC Processor With 125MHz Clock 32 Mbytes System Memory. 512 Kbytes System Boot Flash Memory 4 Mbytes System Flash Memory

1 RS232 Serial Console Interface

GS1002_G2 System software Revision 8.51.008 Released at Tue Jun 5 17:23:35 2012 Program is 2815752 bytes, checksum is 0x16a22bbd

UTC Time is Sat Jun 15 18:05:55 2013 Copyright (c) by AddPac Technology Co., Ltd. Since 1999.

Allocating system mbuffer counter: 1536 Kernel callwheelmask 0x3ff callwheelsize 1024 Local flash disk integrity checking. Loading file system(ver2.2), flash-base: 0xb03d0000 ram-base: 0x956f6f7c Loading secondary file system(ver2.2) flash-base: 0xb03c0000 ram-base: 0x95b52b7 8 Ethernet port initialization complete Ethernet port initialization complete System utilization reference (15/15/15/15) Start Target Debug Server Attach FastEthernet Interface at Slot 0, Port 0-1, <0-0>/<0-1> Interface FastEthernet0/0, changed state to DOWN Interface FastEthernet0/1, changed state to DOWN Hardware Type ID = 2 Hardware Revision ID = 0 Slot (0) AP-GSM2O2 : VoIP module 2 GSM + 2 FXO

Slot (0) Module type : GnO

GsSim Start Start SendMail Server Error occured during reading below line at %s(config)# (5). ip address 192.168.1.11 255.255.255.0

Error occured during reading below line at %s(config)# (5). speed auto

Error occured during reading below line at %s(config)# (5). no qos-control

Error occured during reading below line at %s(config)# (5). ip address 192.168.10.1 255.255.255.0

Error occured during reading below line at %s(config)# (5). speed auto

Error occured during reading below line at %s(config)# (5). no qos-control

Error occured during reading below line at %s(config)# (5). fax protocol t38 redundancy 0

Error occured during reading below line at %s(config)# (5). fax rate 9600

Error occured during reading below line at %s(config)# (5). h323 call start fast

Error occured during reading below line at %s(config)# (5). h323 call tunnel enable

Error occured during reading below line at %s(config)# (5). no call-barring unconfigured-ip-address

Error occured during reading below line at %s(config)# (5). no voip-inbound-call-barring enable

Error occured during reading below line at %s(config)# (5). connection plar 201

Error occured during reading below line at %s(config)# (5). no caller-id enable

Error occured during reading below line at %s(config)# (5). connection plar 203

Error occured during reading below line at %s(config)# (5). no caller-id enable

Error occured during reading below line at %s(config)# (5). port 0/0

Error occured during reading below line at %s(config)# (5). user-name gsm1

Error occured during reading below line at %s(config)# (5). user-password gsm1pass

Error occured during reading below line at %s(config)# (5). translate-outgoing called-number 1

Error occured during reading below line at %s(config)# (5). port 0/2

Error occured during reading below line at %s(config)# (5). user-name fxo1

Error occured during reading below line at %s(config)# (5). user-password fxo1pass

Error occured during reading below line at %s(config)# (5). translate-outgoing called-number 3

Error occured during reading below line at %s(config)# (5). port 0/3

Error occured during reading below line at %s(config)# (5). user-name fxo2

Error occured during reading below line at %s(config)# (5). user-password fxo2pass

Error occured during reading below line at %s(config)# (5). translate-outgoing called-number 4

Error occured during reading below line at %s(config)# (5). session target sip-server

Error occured during reading below line at %s(config)# (5). session protocol sip

Error occured during reading below line at %s(config)# (5). voice-class codec 1

Error occured during reading below line at %s(config)# (5). no vad

Error occured during reading below line at %s(config)# (5). dtmf-relay rtp-2833

Error occured during reading below line at %s(config)# (5). sip-server 109.110.188.171

Error occured during reading below line at %s(config)# (5). called-party-number to-field

Error occured during reading below line at %s(config)# (5). remote-party-id

Error occured during reading below line at %s(config)# (5). register e164

Press RETURN to get started.

RTA Module Ready CPU internal DSP SRAM .... OK Audio DSP S/W download ... OK QSLAC (0) clock sync ..... OK

GsSim Ready get voip interface address fail !

VoipGateway::Init1 - No IP address on the VoIP Interface [25.670] MOBILE-0/0: module initialization failure (err=0x80) MOBILE-0/0: MODULE ID = GC864-QUAD MOBILE-0/1: MODULE ID = GC864-QUAD [29.870] MOBILE-0/1: SIM READY [49.070] Interface MOBILE-0/1, changed state to UP onsole Interface

Автор:  genal [ 12 июл 2013, 11:03 ]
Заголовок сообщения:  Re: GS1002 КОНФИГ ЗАГНУЛСЯ

Попробуйте зайти в Boot режим.
С него загрузить прошивку. Заходить нужно на порт LAN1 телнетом в первые 5 секунд после включения шлюза. Логин/Пароль guest/guest.
Если не получиться можно посмотреть в файловой системе есть ли файл конфигурации, его можно тоже попробовать закинуть по FTP.

Страница 1 из 1 Часовой пояс: UTC
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/